[. . . ] Digital Video Cassette Recorder
E AJEG Operating Instructions DEUTSCH ESPAÑOL ITALIANO FRANÇAIS
ENGLISH
Caution for AC Mains Lead
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable. ONLY If the plug supplied is not suitable for your socket outlet, it should be cut off and appropriate one fitted.
FOR U. K. ONLY
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] Turn the search dial and move the cursor ( ) on the menu screen to any setup item except No. If the USER1 settings are not going to be stored in the memory, do not press the SET button but press the MENU button.
Automatic loading of user file when the power is turned on
When the user file to be loaded is selected in advance using setup menu item No. A02 (P. ON LOAD), it can be automatically loaded into USER1 when the power is turned on.
58 (E)
Setup (setting) menus
SYSTEM menu
<SYSTEM>
Item
No. 0000 0001 0002 0003 0004 0005
Setting
Superimposed display CTL TC VIDEO SYNC RF ENV
Description
This selects the signal to output from the VIDEO OUT 2 connector. The settings can be changed at any time regardless of the setup menu item No. During normal playback, the output signals have levels which are virtually identical to the values given below under a 75 termination. CTL: 0. 1 to 0. 3 Vp-p TC: 0. 6 Vp-p VIDEO: 1. 0 Vp-p SYNC: 0. 25 Vp-p This selects whether the video output signal is to be adjusted on the VTR or with the external encoder remote control. 0: Video output signals are adjusted with the external encoder remote control. System phase adjustment: Total variable range: ±180° or more : Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. System phase adjustment: 74 ns steps : Advanced +: Delayed <Note> If setting operation is performed, the setting value does not return to factory (default) setting. Video phase adjustment: 148 ns steps : Advanced +: Delayed
10
ENCODER SEL
0000 0001
REMOTE LOCAL
11
SYS SC
0000 . 100
12
SYS H
13
VIDEO PHASE
14
SCH COARSE
SCH phase adjustment: 90° units : Advanced +: Delayed (The S and C phases change but the H phase does not change. ) SCH phase adjustment: Total variable range: ±45° or more : Advanced +: Delayed (The S and C phases change but the H phase does not change. ) This adjusts the audio output phase with respect to the video output: 20. 8 µs steps : The audio output phase is advanced with respect to the video output. +: The audio output phase is delayed with respect to the video output.
15
SCH FINE
16
AV PHASE
The underline on the setting item denotes the initial setting.
59 (E)
ENGLISH
Setup (setting) menus
SYSTEM menu
<SYSTEM> (continued)
Item
No. 0000 0001
Setting
Superimposed display FULL FINE
Description
This selects the adjustable range for SYSTEM H during when the ENCODER REMOTE is connected. 0: ±8 µsec 1: 2. 0 to +2. 7 µsec <Notes> · If setting operation is performed, the setting value does not return to factory (default) setting. · FULL operation results regardless of this item's setting if SYSTEM H is varied using this unit instead of the encoder remote controller. System phase adjustment: 0: 13. 4 µsec 1: 8. 96 µsec 2: 4. 52 µsec 3: 0 sec 4: +4. 52 µsec 5: +8. 96 µsec 6: +13. 4 µsec <Note> Factory settings will remain unchanged even if an attempt is made to perform a setting operation. This sets whether the system phase is to be adjusted by the unit or from the external encoder remote controller. 0: The system phase is adjusted from the external encoder remote controller. <Note> This setting does not take effect when LOCAL has been selected as the SYSTEM menu item No. This selects whether the system file lock mode is to be engaged or released. 00 (WFM SEL) can be changed at any time regardless of the setting selected for this menu item.
18
SYS H OFFSET
0000 0001 0002 0003 0004 0005 0006
3 2 1 0 1 2 3
19
SYS SC/H
0000 0001
REMOTE LOCAL
30
MENU LOCK
0000 0001
OFF ON
The underline on the setting item denotes the initial setting.
Video output signal adjustments The video output signal adjustments are made by selecting the SYSTEM menu item No. [. . . ] · When the PLAY button is pressed in 2× speed transmission mode, playback will always be performed at 2× speed and 1× speed playback cannot performed. · In 2× speed transmission mode, the REC INHIBIT lamp will light when a tape is inserted, and recording operations are inhibited. Further, TAPE mode is always established and the EE screen is not output. · When a DV/DVCAM tape is inserted, playback will always be at 1× speed, regardless of the setup menu item No. [. . . ]